Differences

This shows you the differences between two versions of the page.

--- bdev:circuitboard_3dprinter_smoothie_config [2021/09/22 20:44]
richard
+++ bdev:circuitboard_3dprinter_smoothie_config [2021/09/22 22:37] (current)
richard
@@ Line 1: / Line 1: @@
+{{:bdev:ramps_1.4.png?600|}}
+<code>
+* Sorted by      Sorted by
+* Arduino        port and then
+* logical pin    by pin
+* 0_3  D0        0_0  D20
+* 0_2  D1        0_1  D21
+* 1_25 D2        0_2  D1
+* 1_24 D3        0_3  D0
+* 1_18 D4        0_4  D24
+* 1_19 D5        0_5  D28
+* 1_21 D6        0_6  D80
+* 2_7  D8        0_7  D81
+* 2_4  D9        0_8  D82
+* 2_5  D10       0_9  D83
+* 1_20 D11       0_10 D38
+* 2_12 D12       0_11 D55
+* 4_28 D13       0_15 D52
+* 1_26 D14       0_16 D16
+* 1_27 D15       0_17 D50
+* 0_16 D16       0_18 D51
+* 1_29 D18       0_19 D56
+* 1_28 D19       0_20 D61
+* 0_0  D20       0_21 D62
+* 0_1  D21       0_22 D48
+* 0_4  D24       0_23 D67
+* 2_0  D26       0_24 D68
+* 0_5  D28       0_25 D69
+* 4_29 D30       0_26 D63
+* 3_26 D31       0_27 D57
+* 3_25 D33       0_28 D58
+* 2_13 D34       1_0  D78
+* 2_11 D35       1_1  D79
+* 2_8  D36       1_4  D77
+* 1_30 D37       1_8  D76
+* 0_10 D38       1_9  D74
+* 1_22 D41       1_10 D75
+* 2_3  D46       1_14 D73
+* 0_22 D48       1_15 D72
+* 1_31 D49       1_16 D70
+* 0_17 D50       1_17 D71
+* 0_18 D51       1_18 D4
+* 0_15 D52       1_19 D5
+* 1_23 D53       1_20 D11
+* 2_1  D54       1_21 D6
+* 0_11 D55       1_22 D41
+* 0_19 D56       1_23 D53
+* 0_27 D57       1_24 D3
+* 0_28 D58       1_25 D2
+* 2_6  D59       1_26 D14
+* 2_2  D60       1_27 D15
+* 0_20 D61       1_28 D19
+* 0_21 D62       1_29 D18
+* 0_26 D63       1_30 D37
+* 0_23 D67       1_31 D49
+* 0_24 D68       2_0  D26
+* 0_25 D69       2_1  D54
+* 1_16 D70       2_2  D60
+* 1_17 D71       2_3  D46
+* 1_15 D72       2_4  D9
+* 1_14 D73       2_5  D10
+* 1_9  D74       2_6  D59
+* 1_10 D75       2_7  D8
+* 1_8  D76       2_8  D36
+* 1_4  D77       2_11 D35
+* 1_0  D78       2_12 D12
+* 1_1  D79       2_13 D34
+* 0_6  D80       3_25 D33
+* 0_7  D81       3_26 D31
+* 0_8  D82       4_28 D13
+* 0_9  D83       4_29 D30
+*/
+</code>
 http://smoothieware.org/zprobe
@@ Line 26: / Line 107: @@
 | M280 S5.5 |	ZMin test mode (for M119) |
 \\
+<code>
+leveling-strategy.rectangular-grid.enable               true     # The strategy must be enabled in the config, as well as the zprobe module.
+leveling-strategy.rectangular-grid.x_size               75       # size of bed in the X axis
+leveling-strategy.rectangular-grid.y_size               50       # size of bed in the Y axis
+leveling-strategy.rectangular-grid.size                 7 	 # The size of the grid, for example, 7 causes a 7x7 grid with 49 points.
+                                                                 # Must be an odd number.
+leveling-strategy.rectangular-grid.do_home              true
+leveling-strategy.rectangular-grid.probe_offsets        0,0,0    # Optional probe offsets from the nozzle or tool head
+leveling-strategy.rectangular-grid.save                 false    # If the saved grid is to be loaded on boot then this must be set to true
+leveling-strategy.rectangular-grid.initial_height       10       # will move to Z10 before the first probe
+mm_per_line_segment                                     1        # necessary for cartesians using rectangular-grid
+#leveling-strategy.rectangular-grid.before_probe_gcode   M280     # uncomment if you have a bltouch
+#leveling-strategy.rectangular-grid.after_probe_gcode    M281     # uncomment if you have a bltouch
+</code>
+\\
+LCD\\
+\\http://smoothieware.org/panel
+\\
+<code>
+# config settings
+panel.enable                          true              # set to true to enable the panel code
+panel.lcd                             reprap_discount_glcd     # set type of panel
+panel.spi_channel                     0                 # spi channel to use  ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
+panel.spi_cs_pin                      0.16              # spi chip select     ; GLCD EXP1 Pin 4
+panel.encoder_a_pin                   3.25!^            # encoder pin         ; GLCD EXP2 Pin 3
+panel.encoder_b_pin                   3.26!^            # encoder pin         ; GLCD EXP2 Pin 5
+panel.click_button_pin                1.30!^            # click button        ; GLCD EXP1 Pin 2
+panel.buzz_pin                        1.31              # pin for buzzer      ; GLCD EXP1 Pin 1
+panel.back_button_pin                 2.11!^            # 2.11 menu back      ; GLCD EXP2 Pin 8
+# setup for external sd card on the GLCD which uses the onboard sdcard SPI port
+panel.external_sd                     true              # set to true if there is an extrernal sdcard on the panel
+panel.external_sd.spi_channel         1                 # set spi channel the sdcard is on
+panel.external_sd.spi_cs_pin          0.28              # set spi chip select for the sdcard (or any spare pin)
+panel.external_sd.sdcd_pin            0.27!^            # sd detect signal (set to nc if no sdcard detect) (or any spare pin)
+</code>
+<code>
+panel.enable	true	# Set to true to enable the panel interface. Panels are a screen, an encoder wheel and/or a set of buttons, used to control your machine.
+panel.lcd	reprap_discount_glcd	# Type of panel we are connecting. Each panel has a specific interface so we need to specify which panel we will be connecting. The currently supported panel types are Reprap_discount_glcd, St7565_glcd, Ssd1306_oled, Viki2, Mini_viki2 and Universal_adapter.
+panel.spi_channel	0	# SPI channel to use
+panel.spi_cs_pin	0.16	# CS ( Chip Select ) pin to use, this can be used to have several different devices on the same SPI port, as long as each device has a separate CS pin. Note that the RRD GLCD panel does not support this and requires being alone on it's port.
+panel.spi_frequency	500000	# SPI port frequency - some panel need it explicitly set
+panel.contrast	9	# Contrast value for panels that support it ( Viki2, Mini_viki2 and St7565_glcd )
+panel.reverse	false	# If set to true, reverse the screen.
+panel.busy_pin	Nc	# If using the Universal_adapter, this pin can be connected to the adapter to ask it if it is busy or not.
+panel.a0_pin	Nc	# If using a viki or SSD1306 this is needed to drive the C/D pin on the display
+panel.rst_pin	Nc	# If using an SSD1306 this pin is sometimes required and connects to the reset pin on the display
+panel.encoder_a_pin	3.25!^	# A pin for the encoder wheel. Encoders have two pins : A and B. Set to Nc if you use no encoder. ^ defines menu move direction
+panel.encoder_b_pin	3.26!^	# B pin for the encoder wheel. Encoders have two pins : A and B. Set to Nc if you use no encoder. ^ defines menu move direction
+panel.encoder_resolution	2	# the number of pulses the encoder emits per detent/click
+panel.click_button_pin	1.30!^	# Pin for the click ( “enter” ) button
+panel.buzz_pin	1.31	# Pin for the buzzer
+panel.back_button_pin	2.11!^	# Pin for the back button
+panel.up_button_pin	0.1!	# Pin for the up button
+panel.down_button_pin	0.0!	# Pin for the down button
+panel.menu_offset	0	# On some panels, this value must be set to 1. This is a number of lines to offset the menu lines by on screen.
+panel.alpha_jog_feedrate	6000	# X jogging feedrate in millimetres/minute. This is used when jogging using the panel screen.
+panel.beta_jog_feedrate	6000	# Y jogging feedrate in millimetres/minute. This is used when jogging using the panel screen.
+panel.gamma_jog_feedrate	200	# Z jogging feedrate in millimetres/minute. This is used when jogging using the panel screen.
+panel.hotend_temperature	185	# Temperature to set the hotend to when using the pre-heating menu item
+panel.bed_temperature	60	# Temperature to set the bed to when using the pre-heating menu item
+panel.external_sd	true	# Set to true if your panel has an external SD card slot, or if you want to connect a second SD card slot to one of your Smothieboard's SPI ports
+panel.external_sd.spi_channel	0	# Set the SPI channel the external SD card is on
+panel.external_sd.spi_cs_pin	2.8	# Set the CS ( Chip Select ) pin for the external SD card, this allows you to use multiple devices on the same SPI port, as long as they each have a CS pin
+panel.external_sd.sdcd_pin	2.13!^	# SD card detect signal pin, set to Nc if you don't use a SD card detect signal
+custom_menu.menu_name.enable	true	# When set to true, create a new custom menu entry for the panel with the name menu_name. You can create any number of custom entries as long as they have different names. NOTE menu_name is case sensitive
+custom_menu.menu_name.name	Power_on	# The name that will be displayed in the panel's menus
+custom_menu.menu_name.command	M80_S30|G1_X10	# The command that will be executed when the menu entry is selected and clicked. Note that the _ character gets converted to space in the menu and commands ( and must be used instead of the space character ) , and the | character is used to separate multiple commands
+</code>
+\\
 <code | smoothie config labbot 3-D printer>
@@ Line 248: / Line 411: @@
 # Example viki2 config for an azteeg mini V2 with IDC cable
-panel.lcd                                    universal_adapter             # set type of panel
+panel.lcd                                    reprap_discount_glcd             # set type of panel
 panel.spi_channel                            0                 # set spi channel to use P0_18,P0_15 MOSI,SCLK
 panel.spi_cs_pin                             0.16              # set spi chip select

labautobox

User Tools

Site Tools

Differences

Page Tools