| Both sides previous revision
Previous revision
Next revision
|
Previous revision
|
bdev:circuitboard_3dprinter_smoothie_config [2021/09/22 22:01]
richard |
bdev:circuitboard_3dprinter_smoothie_config [2021/09/22 22:37] (current)
richard |
| | {{:bdev:ramps_1.4.png?600|}} |
| | |
| | |
| <code> | <code> |
| |
| |
| \\ | \\ |
| | LCD\\ |
| | |
| | \\http://smoothieware.org/panel |
| | \\ |
| | <code> |
| | |
| | # config settings |
| | panel.enable true # set to true to enable the panel code |
| | panel.lcd reprap_discount_glcd # set type of panel |
| | panel.spi_channel 0 # spi channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK) |
| | panel.spi_cs_pin 0.16 # spi chip select ; GLCD EXP1 Pin 4 |
| | panel.encoder_a_pin 3.25!^ # encoder pin ; GLCD EXP2 Pin 3 |
| | panel.encoder_b_pin 3.26!^ # encoder pin ; GLCD EXP2 Pin 5 |
| | panel.click_button_pin 1.30!^ # click button ; GLCD EXP1 Pin 2 |
| | panel.buzz_pin 1.31 # pin for buzzer ; GLCD EXP1 Pin 1 |
| | panel.back_button_pin 2.11!^ # 2.11 menu back ; GLCD EXP2 Pin 8 |
| | # setup for external sd card on the GLCD which uses the onboard sdcard SPI port |
| | panel.external_sd true # set to true if there is an extrernal sdcard on the panel |
| | panel.external_sd.spi_channel 1 # set spi channel the sdcard is on |
| | panel.external_sd.spi_cs_pin 0.28 # set spi chip select for the sdcard (or any spare pin) |
| | panel.external_sd.sdcd_pin 0.27!^ # sd detect signal (set to nc if no sdcard detect) (or any spare pin) |
| | |
| | </code> |
| | |
| | |
| | <code> |
| | panel.enable true # Set to true to enable the panel interface. Panels are a screen, an encoder wheel and/or a set of buttons, used to control your machine. |
| | panel.lcd reprap_discount_glcd # Type of panel we are connecting. Each panel has a specific interface so we need to specify which panel we will be connecting. The currently supported panel types are Reprap_discount_glcd, St7565_glcd, Ssd1306_oled, Viki2, Mini_viki2 and Universal_adapter. |
| | panel.spi_channel 0 # SPI channel to use |
| | panel.spi_cs_pin 0.16 # CS ( Chip Select ) pin to use, this can be used to have several different devices on the same SPI port, as long as each device has a separate CS pin. Note that the RRD GLCD panel does not support this and requires being alone on it's port. |
| | panel.spi_frequency 500000 # SPI port frequency - some panel need it explicitly set |
| | panel.contrast 9 # Contrast value for panels that support it ( Viki2, Mini_viki2 and St7565_glcd ) |
| | panel.reverse false # If set to true, reverse the screen. |
| | panel.busy_pin Nc # If using the Universal_adapter, this pin can be connected to the adapter to ask it if it is busy or not. |
| | panel.a0_pin Nc # If using a viki or SSD1306 this is needed to drive the C/D pin on the display |
| | panel.rst_pin Nc # If using an SSD1306 this pin is sometimes required and connects to the reset pin on the display |
| | panel.encoder_a_pin 3.25!^ # A pin for the encoder wheel. Encoders have two pins : A and B. Set to Nc if you use no encoder. ^ defines menu move direction |
| | panel.encoder_b_pin 3.26!^ # B pin for the encoder wheel. Encoders have two pins : A and B. Set to Nc if you use no encoder. ^ defines menu move direction |
| | panel.encoder_resolution 2 # the number of pulses the encoder emits per detent/click |
| | panel.click_button_pin 1.30!^ # Pin for the click ( “enter” ) button |
| | panel.buzz_pin 1.31 # Pin for the buzzer |
| | panel.back_button_pin 2.11!^ # Pin for the back button |
| | panel.up_button_pin 0.1! # Pin for the up button |
| | panel.down_button_pin 0.0! # Pin for the down button |
| | panel.menu_offset 0 # On some panels, this value must be set to 1. This is a number of lines to offset the menu lines by on screen. |
| | panel.alpha_jog_feedrate 6000 # X jogging feedrate in millimetres/minute. This is used when jogging using the panel screen. |
| | panel.beta_jog_feedrate 6000 # Y jogging feedrate in millimetres/minute. This is used when jogging using the panel screen. |
| | panel.gamma_jog_feedrate 200 # Z jogging feedrate in millimetres/minute. This is used when jogging using the panel screen. |
| | panel.hotend_temperature 185 # Temperature to set the hotend to when using the pre-heating menu item |
| | panel.bed_temperature 60 # Temperature to set the bed to when using the pre-heating menu item |
| | panel.external_sd true # Set to true if your panel has an external SD card slot, or if you want to connect a second SD card slot to one of your Smothieboard's SPI ports |
| | panel.external_sd.spi_channel 0 # Set the SPI channel the external SD card is on |
| | panel.external_sd.spi_cs_pin 2.8 # Set the CS ( Chip Select ) pin for the external SD card, this allows you to use multiple devices on the same SPI port, as long as they each have a CS pin |
| | panel.external_sd.sdcd_pin 2.13!^ # SD card detect signal pin, set to Nc if you don't use a SD card detect signal |
| | custom_menu.menu_name.enable true # When set to true, create a new custom menu entry for the panel with the name menu_name. You can create any number of custom entries as long as they have different names. NOTE menu_name is case sensitive |
| | custom_menu.menu_name.name Power_on # The name that will be displayed in the panel's menus |
| | custom_menu.menu_name.command M80_S30|G1_X10 # The command that will be executed when the menu entry is selected and clicked. Note that the _ character gets converted to space in the menu and commands ( and must be used instead of the space character ) , and the | character is used to separate multiple commands |
| | </code> |
| | |
| | |
| | \\ |
| | |
| | |
| | |
| |
| <code | smoothie config labbot 3-D printer> | <code | smoothie config labbot 3-D printer> |
| |
| # Example viki2 config for an azteeg mini V2 with IDC cable | # Example viki2 config for an azteeg mini V2 with IDC cable |
| panel.lcd universal_adapter # set type of panel | panel.lcd reprap_discount_glcd # set type of panel |
| panel.spi_channel 0 # set spi channel to use P0_18,P0_15 MOSI,SCLK | panel.spi_channel 0 # set spi channel to use P0_18,P0_15 MOSI,SCLK |
| panel.spi_cs_pin 0.16 # set spi chip select | panel.spi_cs_pin 0.16 # set spi chip select |
