bdev:rearm_marlin
Warning: Undefined array key -1 in /var/www/html/dokuwiki/inc/html.php on line 1458
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
bdev:rearm_marlin [2021/10/04 16:11] richard |
bdev:rearm_marlin [2021/10/27 23:08] (current) richard |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Re-ARM Marlin ====== | ====== Re-ARM Marlin ====== | ||
| + | \\ | ||
| + | My latest back up | ||
| + | {{ : | ||
| + | \\ | ||
| + | |||
| \\ | \\ | ||
| https:// | https:// | ||
| Line 6: | Line 11: | ||
| Z probe https:// | Z probe https:// | ||
| \\ | \\ | ||
| + | |||
| + | \\ | ||
| + | Set steps per mm\\ | ||
| + | https:// | ||
| + | \\ | ||
| + | \\ | ||
| + | Cold extrusion\\ | ||
| + | https:// | ||
| + | < | ||
| + | M302 ; report current cold extrusion state | ||
| + | M302 P0 ; enable cold extrusion checking | ||
| + | M302 P1 ; disable cold extrusion checking | ||
| + | M302 S0 ; always allow extrusion (disable checking) | ||
| + | M302 S170 ; only allow extrusion above 170 | ||
| + | M302 S170 P1 ; set min extrude temp to 170 but leave disabled | ||
| + | </ | ||
| + | |||
| + | \\ | ||
| + | Bed size | ||
| + | < | ||
| + | #define X_BED_SIZE 340 | ||
| + | #define Y_BED_SIZE 280 | ||
| + | </ | ||
| + | |||
| \\Heater pin | \\Heater pin | ||
| Line 11: | Line 40: | ||
| #define HEATER_0_PIN | #define HEATER_0_PIN | ||
| #define HEATER_BED_PIN | #define HEATER_BED_PIN | ||
| + | #define FAN_PIN | ||
| </ | </ | ||
| Line 97: | Line 127: | ||
| {% endif %} | {% endif %} | ||
| </ | </ | ||
| - | |||
| - | |||
| + | \\ | ||
| + | Notes on baby stepping https:// | ||
| + | \\ | ||
| + | https:// | ||
| \\ | \\ | ||
| Zprobe set up \\ | Zprobe set up \\ | ||
| Line 106: | Line 138: | ||
| #define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. | #define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. | ||
| #define Z_SERVO_ANGLES { 100, 0 } // Z Servo Deploy and Stow angles | #define Z_SERVO_ANGLES { 100, 0 } // Z Servo Deploy and Stow angles | ||
| - | |||
| </ | </ | ||
| + | \\ | ||
| + | Offsets for Z probe\\ | ||
| + | https:// | ||
| + | \\ | ||
| + | Zprobe bilinear\\ | ||
| + | G29 L20 R330 F20 B250 V4 | ||
| + | \\ | ||
| + | https:// | ||
| + | \\ | ||
| + | Zprobe offsets set up via gcode\\ | ||
| + | https:// | ||
| + | \\ | ||
| + | set up via configuration.h\\ | ||
| + | < | ||
| + | #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 } | ||
| + | </ | ||
| + | |||
| + | \\ | ||
| + | https:// | ||
| \\ | \\ | ||
bdev/rearm_marlin.1633363887.txt.gz ยท Last modified: 2021/10/04 16:11 by richard
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
