Re-ARM Marlin
My latest back up
marlinfirmware.zip
https://github.com/MarlinFirmware/Marlin
https://www.youtube.com/watch?v=H-c8UTg-EMU
Z probe https://www.thingiverse.com/thing:2841443
Set steps per mm
https://marlinfw.org/docs/gcode/M092.html
Cold extrusion
https://marlinfw.org/docs/gcode/M302.html
M302 ; report current cold extrusion state M302 P0 ; enable cold extrusion checking M302 P1 ; disable cold extrusion checking M302 S0 ; always allow extrusion (disable checking) M302 S170 ; only allow extrusion above 170 M302 S170 P1 ; set min extrude temp to 170 but leave disabled
Bed size
#define X_BED_SIZE 340 #define Y_BED_SIZE 280
\\Heater pin
#define HEATER_0_PIN RAMPS_D10_PIN #define HEATER_BED_PIN RAMPS_D8_PIN #define FAN_PIN RAMPS_D9_PIN
Octoprint filament sensor set up using Raspberry Pi
https://www.thingiverse.com/thing:2095911
https://www.youtube.com/watch?v=ChjwIGxnivw
https://www.thingiverse.com/thing:2095911
Filament sensor reloaded plugin
https://github.com/ssorgatem/Octoprint-Filament-Reloaded
octoprint-filament-reloaded.zip
GPIO 18 and 20
After print job is paused
{% if pause_position.x is not none %}
; relative XYZE
G91
M83
; retract filament of 0.8 mm up, move Z slightly upwards and
G1 Z+5 E-0.8 F4500
; absolute XYZE
M82
G90
; move to a safe rest position, adjust as necessary
G1 X0 Y0
{% endif %}
Before print job is resumed
{% if pause_position.x is not none %}
; relative extruder
M83
; prime nozzle
G1 E-0.8 F4500
G1 E0.8 F4500
G1 E0.8 F4500
; absolute E
M82
; absolute XYZ
G90
; reset E
G92 E{{ pause_position.e }}
; WARNING!!! - use M83 or M82(exruder absolute mode) according what your slicer generates
M83 ; extruder relative mode
; move back to pause position XYZ
G1 X{{ pause_position.x }} Y{{ pause_position.y }} Z{{ pause_position.z }} F4500
; reset to feed rate before pause if available
{% if pause_position.f is not none %}G1 F{{ pause_position.f }}{% endif %}
{% endif %}
Notes on baby stepping https://community.octoprint.org/t/how-to-still-control-z-adjustment-during-print/19413/11
https://3dprintbeginner.com/octoprint-baby-stepping/
Zprobe set up
#define Z_MIN_PROBE_PIN P1_28 //Z_MAX_PIN
#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
#define Z_SERVO_ANGLES { 100, 0 } // Z Servo Deploy and Stow angles
Offsets for Z probe
https://marlinfw.org/docs/gcode/M851.html
Zprobe bilinear
G29 L20 R330 F20 B250 V4
https://marlinfw.org/docs/gcode/G029-abl-bilinear.html
Zprobe offsets set up via gcode
https://marlinfw.org/docs/gcode/M851.html
set up via configuration.h
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
https://marlinfw.org/docs/gcode/M280.html
SERVO set up
#define NUM_SERVOS 1 // Note: Servo index starts with 0 for M280-M282 commands
// (ms) Delay before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY { 300 }
// Only power servos during movement, otherwise leave off to prevent jitter
#define DEACTIVATE_SERVOS_AFTER_MOVE
* Sorted by Sorted by * Arduino port and then * logical pin by pin * 0_3 D0 0_0 D20 * 0_2 D1 0_1 D21 * 1_25 D2 0_2 D1 * 1_24 D3 0_3 D0 * 1_18 D4 0_4 D24 * 1_19 D5 0_5 D28 * 1_21 D6 0_6 D80 * 2_7 D8 0_7 D81 * 2_4 D9 0_8 D82 * 2_5 D10 0_9 D83 * 1_20 D11 0_10 D38 * 2_12 D12 0_11 D55 * 4_28 D13 0_15 D52 * 1_26 D14 0_16 D16 * 1_27 D15 0_17 D50 * 0_16 D16 0_18 D51 * 1_29 D18 0_19 D56 * 1_28 D19 0_20 D61 * 0_0 D20 0_21 D62 * 0_1 D21 0_22 D48 * 0_4 D24 0_23 D67 * 2_0 D26 0_24 D68 * 0_5 D28 0_25 D69 * 4_29 D30 0_26 D63 * 3_26 D31 0_27 D57 * 3_25 D33 0_28 D58 * 2_13 D34 1_0 D78 * 2_11 D35 1_1 D79 * 2_8 D36 1_4 D77 * 1_30 D37 1_8 D76 * 0_10 D38 1_9 D74 * 1_22 D41 1_10 D75 * 2_3 D46 1_14 D73 * 0_22 D48 1_15 D72 * 1_31 D49 1_16 D70 * 0_17 D50 1_17 D71 * 0_18 D51 1_18 D4 * 0_15 D52 1_19 D5 * 1_23 D53 1_20 D11 * 2_1 D54 1_21 D6 * 0_11 D55 1_22 D41 * 0_19 D56 1_23 D53 * 0_27 D57 1_24 D3 * 0_28 D58 1_25 D2 * 2_6 D59 1_26 D14 * 2_2 D60 1_27 D15 * 0_20 D61 1_28 D19 * 0_21 D62 1_29 D18 * 0_26 D63 1_30 D37 * 0_23 D67 1_31 D49 * 0_24 D68 2_0 D26 * 0_25 D69 2_1 D54 * 1_16 D70 2_2 D60 * 1_17 D71 2_3 D46 * 1_15 D72 2_4 D9 * 1_14 D73 2_5 D10 * 1_9 D74 2_6 D59 * 1_10 D75 2_7 D8 * 1_8 D76 2_8 D36 * 1_4 D77 2_11 D35 * 1_0 D78 2_12 D12 * 1_1 D79 2_13 D34 * 0_6 D80 3_25 D33 * 0_7 D81 3_26 D31 * 0_8 D82 4_28 D13 * 0_9 D83 4_29 D30 */
